Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
- Steering
   12.2. The general description
   12.3. The reechnyj steering mechanism in gathering
   12.4. Tips of steering draughts
   12.5. Steering draughts
   12.6. A casing картера the steering mechanism
   12.7. Муфта a steering shaft
   12.8. A sealing cover of an aperture of a forward board of the Body
   12.9. Плунжер рейки
   12.10. The Shaft-gear wheel
   12.11. Рейка
   12.12. The needle bearing
   12.13. The directing plug рейки
   12.14. Check of neutral position рейки
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added a working liquid
   12.17. Removal of air from hydrosystem
   12.18. The steering mechanism with the hydraulic booster in gathering
   12.19. Hoses and pipelines
   12.20. A tank
   12.21. Tips of steering draughts
   12.22. Steering draughts
   12.23. Plugs of hinges of steering draughts
   12.24. Муфта a steering shaft
   12.25. A sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring плунжера
   12.28. Consolidations of a shaft of the hydrodistributor and the top bearing
   12.29. The steering mechanism
   12.30. Check of neutral position рейки
   12.31. A belt of a drive of the pump
   12.32. A pulley of a drive of the pump
   12.33. The pump in gathering
   12.34. Control levers on a steering column
   12.35. A steering wheel
   12.36. The ignition lock
   12.37. A steering column
   12.38. Lever the switch, a steering shaft, a steering column (noncontrollable)
   12.39. Lever the switch, a steering shaft, a steering column (regulated)
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment



12.39. Lever the switch, a steering shaft, a steering column (regulated)
THE GENERAL DATA

Steering column with an adjustable angle of slope of a steering wheel for cars with automatic transmission and a hand-operated transmission

1. THE NUT
2. THE SPRING OF THE MECHANISM OF DEENERGIZING OF INDEXES OF TURN
3. THE SPRING RING
4. THE HOLDER
5. THE SPRING OF THE TOP BEARING
6. THE SCREW
7. THE CASE FOR FASTENING OF LEVER SWITCHES
8. THE SADDLE
9. THE INTERNAL RING
10. СРЕЗНОЙ THE BOLT
11. THE WASHER
12. THE ROTARY CASE OF THE COLUMN
13. THE AXIS OF THE ROTARY CASE
14. THE CASE FOR FASTENING OF THE LOCK OF IGNITION
15. THE SWITCH OF THE LOCK OF IGNITION
16. THE ADJUSTING SCREW
17. THE SPRING OF THE MECHANISM OF CHANGE OF THE ANGLE OF SLOPE OF THE STEERING WHEEL
18. THE HOLDER OF THE SPRING
19. ШАРНИРНЫЙ THE STEERING SHAFT IN GATHERING
20. THE TOP STEERING SHAFT
21. THE HEMISPHERICAL CRACKER
22. THE SPRING
23. THE BOTTOM STEERING SHAFT
24. THE EMPHASIS OF THE ROTARY CASE
25. THE BOLT
26. THE SUPPORT OF THE STEERING COLUMN
27. THE CASING OF THE STEERING COLUMN

To remove or disconnect

Dismantle and installation of a spring ring


3. THE SPRING RING
20. THE TOP PART OF THE STEERING SHAFT

Dismantle of axes of the rotary case of a steering column

12. THE ROTARY CASE OF THE COLUMN
13. THE AXIS OF THE ROTARY CASE

PERFORMANCE ORDER
1. A steering wheel.
2. A steering column in gathering.
3. Directing plug 28 bottom ends of a steering shaft 19 (if it has not been dismantled earlier).
4. A spring 2 from the top end of a shaft 19 (if it has not been dismantled earlier).
5. Screws 6.
6. The case of 7 lever switches.
7. To compress a spring 5 through the holder 4.
8. A spring ring 3, the holder 4, a spring 5, a saddle 8 and an internal ring 9.
9. To pull for the lever of an inclination of the column, located on the case 12, and to lift a steering wheel upwards against the stop.
10. To insert крестовую a screw-driver into a square aperture of the holder of 18 springs, to press downwards and, having turned a screw-driver counter-clockwise, to release the holder 18 and a spring 17.
11. The holder 18 and a spring 17.
12. Two axes 13.
13. To turn the lock cylinder in position "RUN" (Ignition is included).
14. To pull the lever of adjustment of an inclination of a steering wheel and to take out the rotary case 12 of a support 26 steering columns.
15. Sreznye bolts 10, washers 11 and to disconnect the case of 14 fastenings of the lock of ignition from the rotary case 12.
15а. To drill heads срезных bolts 10 to steel washers 11. To use a drill in diameter of 6,5 mm, fig. Initial and final positions of a shaft-gear wheel see.
15б. To remove washers 11, to disconnect the case 14 from the rotary case 12 steering columns.
15в. To turn out cores of bolts 10 of the case 14 by means of flat-nose pliers.
The prevention

After operation высверлива ния heads of bolts it is necessary to clear details of a shaving.


16. The cylinder of the lock of ignition from the case 14.
17. To turn out the adjusting screw 16.
18. The switch of ignition 15 in gathering.
19. To take out a steering shaft 19 in gathering through an aperture of a support 26.
20. An emphasis 24 by means of flat-nose pliers.
21. Bolts 25 and to disconnect a support 26 from a flange of a casing 27 steering columns.

To disassemble

Dismantling and assemblage of the hinge of a steering shaft

20. THE TOP STEERING SHAFT
21. THE HEMISPHERICAL CRACKER
22. THE SPRING
23. THE BOTTOM STEERING SHAFT

If necessary repair шарнирного a steering shaft 19 is spent as follows.
The prevention

Before disconnecting from each other top 20 and the bottom 23 parts of a steering shaft, it is necessary to notice a relative positioning of a longitudinal flute on a shaft 20 and лыски under a coupling bolt on a shaft 23. If to turn a steering shaft 19 so that a flute under a uvula of blocking of a steering shaft settled down from above (the hour hand is at 12 o'clock) position лыски should correspond to an hour hand specifying at 7 o'clock. At assemblage of a detail of a steering shaft should be established in the same position.


PERFORMANCE ORDER
1. To turn a steering shaft 20 on 90 degrees concerning the bottom shaft 23 and to disconnect last from the hinge, fig. Dismantle of axes of the rotary case of a steering column see.
2. To turn a spherical cracker on 90 degrees and to take out it from a plug of a shaft 20.
3. To separate hemispherical crackers 21 and to remove preliminary loaded spring 22.

To collect

Correct mutual position of the top and bottom steering shaft

20. THE TOP STEERING SHAFT
23. THE BOTTOM STEERING SHAFT

PERFORMANCE ORDER
1. To grease hemispherical crackers 21 and a spring 22 консистентной литиевой with greasing.
2. To establish a spring 22 between hemispherical crackers 21, having inserted the spring ends into corresponding grooves of crackers, fig. Dismantle of axes of the rotary case of a steering column see.
3. To grease a plug of the top shaft 20 консистентной литиевой with greasing.
4. To insert crackers 21 in gathering into a plug of a shaft 20 and to develop them on 90 degrees.
5. To grease a plug of the bottom shaft 23 консистентной литиевой with greasing.
The prevention

For correct assemblage top 20 and the bottom 23 steering shaft to execute the following. To turn the top shaft 20 so that a flute under a uvula of blocking of a steering shaft settled down from above (an hour hand at 12 o'clock). Лыска on the end of the bottom shaft 23 should settle down from below at the left (the hour hand at 7 o'clock), see fig. Correct mutual position of the top and bottom steering shaft.


6. To develop the top shaft 20 on 90 degrees concerning the bottom shaft 23.
7. To insert a plug of a shaft 23 into the hinge and to straighten a steering shaft in gathering.

To establish or attach

The prevention

All fixing details used in described below assembly operations, should be densely wrapped before a definitive inhaling the moment of the demanded size.


PERFORMANCE ORDER
1. A support 26 to a flange of a casing 27 by means of bolts 25. To tighten bolts the moment of 16 Nanometers.
2. An emphasis 24 about a support 26 and a spring ring into place.
3. To insert a steering shaft 19 into an aperture of a support 26.
4. To grease both bearings of the rotary case of 12 columns консистентной литиевой with greasing.
5. To establish the case 12 on a shaft 19 and in a support 26.
6. To grease axes 13 консистентной литиевой with greasing
7. To insert axes 13 into apertures of the case 12 against the stop.
The prevention

After installation it is necessary закернить for an axis 13 in the case 12. Кернить each axis in three places in regular intervals located on a circle.


8. To pull for the mechanism lever регулиро вания an angle of slope of a steering wheel and to lift a steering wheel as much as possible upwards.
9. To grease a spring 17 mechanisms of adjustment of an angle of slope of a steering wheel консистентной литиевой with greasing.
10. A spring 17 and the holder 18. To be convinced that the end of a spring 17 is put on a hook of a support 26. To insert крестовую a screw-driver into a square aperture of the holder of 18 springs, to press downwards and having turned a screw-driver clockwise, to fix the holder 18.
The prevention

To provide at installation coincidence of a uvula of the cylinder of the lock and a groove of the switch of ignition 15, it is necessary to turn preliminary them in position "RUN".


11. The switch of ignition 15 in the case 14. To be convinced that the pin has entered into an aperture of an eye of the switch 15.
12. To screw the adjusting screw 16 and to tighten it by hand (the moment about 0,3 Nanometers).
13. The cylinder of the lock of ignition about the case 14.
14. To attach the case 14 to the rotary case 12 steering columns by means of washers 11 and срезных bolts 10. To tighten bolts and to cut off heads, having put a twisting moment about 11 Nanometers.
15. To turn the cylinder of the lock of ignition position "OFF-LOCK" and to take out a key.
16. To turn a steering shaft 19 before operation of the lock of blocking.
17. An internal ring 9, a saddle 8, a spring 5 top bearings and the holder 4.
18. To press on the holder 4 and to compress a spring 5, fig. Dismantle and installation of a spring ring see.
19. A spring ring 3 in a flute on the top helmsman to a shaft 20.
20. The case of 7 lever switches on the rotary case 12. To screw screws 6 and to tighten their moment of 3,4 Nanometers.
21. Directing plug 28 on the bottom end of a steering shaft 23 and in a nest of a casing 27.
22. A steering column in gathering on the car.
The prevention

After connection of a steering shaft with a shaft of the steering mechanism to take out directing plug 28 of a casing 27 and to leave it on the helmsman to a shaft 19 for use further.


23. A spring 21 mechanisms of deenergizing of indexes of turn and a steering wheel on a shaft.
24. To screw a nut 1 and to tighten its moment of 17 Nanometers.






девочки