Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
- Maintenance service
   1.2. The general instructions on repair
   1.2. Identification number of the car
   1.3. Car lifting
   1.4. Car maintenance service
   + 1.5. Control surveys and the servicing, spent by the owner
   1.6. The moments of an inhaling of carving connections
   1.7. Characteristics of the car with system of multidot injection of fuel
   1.8. Characteristics of cars (2 top camshafts of the engine)
   1.9. The sizes and weight of cars
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


1cb365f7

Maintenance service

1. Maintenance service

1.1. The general information
THE GENERAL DATA

Safety precautions key rules

Appropriate Maintenance service and repair are very important from the point of view of safe operation and reliability of the car. In the given management effective and correct receptions of carrying out of all necessary operations on servicing and car repairs are described. Application of special tools and adaptations in certain cases is required. These tools and adaptations should be used in strict conformity with recommendations.

At work with an Electric equipment, connected with short circuit possibility, it is necessary to disconnect "a mass" wire of the storage battery. After battery connection it is necessary to establish anew indications of the electric clock, to repeat adjustment and to bring in memory of a radio receiver of frequency of stations of an announcement, and also to reprogram other electronic equipment of the car. Stated above caution are not settling. Company DEU cannot, naturally, in advance to provide all possible variants of technological operations and dangerous situations which can arise at carrying out of repair and car maintenance service. Therefore before putting into practice any reception or the tool which is distinct from that are recommended in the given management, it is very important to be convinced of safety for the personnel and the car. In the given management of operation on maintenance service and repair are described, basically, for cars with a link sided steering. On cars with a right-hand steering all operations are spent similarly (in mirror reflexion). Functions of various systems and car devices do not depend on a steering variant. In the presence of any essential features of cars with various variants of a steering in a management the corresponding additional information is resulted.

The general instructions on repair

At use of a floor jack it is necessary to observe following rules. Put the car on a horizontal platform. Block from possible movings a forward or back wheel. Establish a jack under a basic nest of the Body and lift the car. Substitute under the car safety rigid support. Only after that it is possible to start servicing or repair carrying out.

Before work DISCONNECT "the MASS" WIRE of the storage battery in order to avoid damages of the car and traumas because of short circuit.

Use safety covers for protection of the Body, seats and rugs on a floor from damages and pollution. Do not suppose hit of a brake liquid and a cooling liquid on a car Body as they can damage a paint and varnish covering.

Use only the serviceable tool recommended in the given management.

The reuse шплинтов, linings, sealing rings of round section, манжетных consolidations, lock washers and самоконтрящихся nuts is not supposed. At assemblage of units it is necessary to replace with their new details. Otherwise normal work of units cannot be guaranteed.

For simplification and acceleration of assemblage of units accurately store the disassembled details in separate groups.

Do not confuse various fixing bolts and nuts as they differ on durability and design features depending on an installation site.

Clear details of pollution before their survey or installation.

Details of oil systems also are subject to clearing and a purge the compressed air for removal of all pollution.

Before installation of details grease sliding and rotation surfaces with liquid oil or консистентной greasing.

If necessary for elimination of a leak of oil or operational liquids use hermetic together with sealing linings.

Carefully observe requirements to size of the moment of a tightening of bolts and nuts.

After servicing or repair end spend final check to be convinced of correct performance of all operations and malfunction elimination.