Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
- Steering
   12.2. The general description
   12.3. The reechnyj steering mechanism in gathering
   12.4. Tips of steering draughts
   12.5. Steering draughts
   12.6. A casing картера the steering mechanism
   12.7. Муфта a steering shaft
   12.8. A sealing cover of an aperture of a forward board of the Body
   12.9. Плунжер рейки
   12.10. The Shaft-gear wheel
   12.11. Рейка
   12.12. The needle bearing
   12.13. The directing plug рейки
   12.14. Check of neutral position рейки
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added a working liquid
   12.17. Removal of air from hydrosystem
   12.18. The steering mechanism with the hydraulic booster in gathering
   12.19. Hoses and pipelines
   12.20. A tank
   12.21. Tips of steering draughts
   12.22. Steering draughts
   12.23. Plugs of hinges of steering draughts
   12.24. Муфта a steering shaft
   12.25. A sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring плунжера
   12.28. Consolidations of a shaft of the hydrodistributor and the top bearing
   12.29. The steering mechanism
   12.30. Check of neutral position рейки
   12.31. A belt of a drive of the pump
   12.32. A pulley of a drive of the pump
   12.33. The pump in gathering
   12.34. Control levers on a steering column
   12.35. A steering wheel
   12.36. The ignition lock
   12.37. A steering column
   12.38. Lever the switch, a steering shaft, a steering column (noncontrollable)
   12.39. Lever the switch, a steering shaft, a steering column (regulated)
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


1cb365f7

12.10. The Shaft-gear wheel
THE GENERAL DATA

Dismantle and installation of consolidation of a shaft-gear wheel

A. TO PUT ON CONTACTING SURFACES OF THE SHAFT-GEAR WHEEL AND CONSOLIDATION THE GREASING CONTAINING КАЛЬЦИЕВЫЙ ANHYDRIDE
CENTURY CONSOLIDATION SHOULD SETTLE DOWN ЗАПОДЛИЦО WITH CARTER'S END FACE

4. CONSOLIDATION
5. THE SHAFT THE GEAR WHEEL

Initial and final positions of a shaft-gear wheel

AND. INITIAL POSITION (7:30)
CENTURY FINAL POSITION (9:00)
WITH. MIDDLE ЛЫСКИ FOR INITIAL POSITION
D. MIDDLE ЛЫСКИ FOR FINAL POSITION

7. CARTER

To remove or disconnect

Shaft-gear wheel dismantle

5. THE SHAFT-GEAR WHEEL
11. THE SPRING RING

Dismantle of a shaft-gear wheel from картера

AND. TO KNOCK ON CARTER FOR SIMPLIFICATION OF DISMANTLE OF THE SHAFT-GEAR WHEEL
CENTURY THE VICE WITH OVERLAYS OF SPONGES FROM THE SOFT MATERIAL
WITH. THE HAMMER

5. THE SHAFT-GEAR WHEEL
9. THE RUBBER PLUG


PERFORMANCE ORDER
1. To turn a shaft-gear wheel 5 so that a directing lath 10 was in the middle of a window картера.
2. To note position лыски a shaft-gear wheel rather картера.
3. A spring ring 11.
4. The Shaft-gear wheel 5.

To measure

PERFORMANCE ORDER
The directing lath 10 should be in the middle of a window картера.

To establish or attach

Arrangement of a directing lath in a window картера


AND. IDENTICAL DISTANCES
CENTURY CARTER'S WINDOW

10. DIRECTING PLANCK

PERFORMANCE ORDER
1. The Shaft-gear wheel. Position лыски a shaft-gear wheel should correspond put on картер the mechanism to a label, the lath 10 will be thus located in the middle of a window картера.
2. A spring ring 11.