Daewoo Nexia

Since 1994 of release

Repair and car operation

12.38. Lever the switch, a steering shaft, a steering column (noncontrollable)

THE GENERAL DATA

Steering column – standard execution for cars with automatic transmission and a hand-operated transmission

1. THE NUT 2. THE SPRING 3. THE PERSISTENT WASHER 4. THE SCREW 5. THE CASE FOR FASTENING OF LEVER SWITCHES 6. СРЕЗНОЙ THE BOLT 7. СРЕЗНОЙ THE BOLT

8. THE WASHER 9. THE TOP CASE OF THE STEERING COLUMN 10. THE CASING OF THE STEERING COLUMN 11. THE DIRECTING PLUG 12. THE CASE FOR FASTENING OF THE LOCK OF IGNITION 13. THE ADJUSTING SCREW 14. THE SWITCH OF THE LOCK OF IGNITION 15. THE STEERING SHAFT

To remove or disconnect

Dismantle срезного a bolt

7. СРЕЗНОЙ THE BOLT 9. THE TOP CASE OF THE STEERING COLUMN 12. THE CASE FOR FASTENING OF THE LOCK OF IGNITION

PERFORMANCE ORDER

1. A steering wheel. 2. A steering column in gathering. 3. Directing plug 11 bottom ends of a steering shaft 15 if it has not been dismantled earlier). 4. A spring 2 from the top end of a steering shaft 15. 5. A persistent washer 3. 6. Screws 4. 7. To turn the case of 5 lever switches. 8. To turn the lock cylinder in position "RUN" (ignition is switched off). 9. To take out a steering shaft 15 through the bottom aperture of a casing 10. 10. Sreznye bolts 7, washers 8 and the case of fastening of the lock of ignition. 10а. To drill heads срезных bolts 7 to steel washers 8. To use a drill in diameter of 6.5 mm, fig. Dismantle срезного a bolt see. 10б. To remove washers 8, to disconnect the case 12 from the top case 9 steering columns. 10в. To turn out cores of bolts 7 of the case 12 by means of flat-nose pliers. The prevention After operation of drilling of heads of bolts it is necessary to clear details of a shaving. 11. The cylinder of the lock of ignition from the case 12. 12. To turn out the adjusting screw 13. 13. The switch of ignition 14 in gathering. 14. Sreznye bolts 6 and the top case of a steering column. 14а. To drill heads срезных bolts 6 by means of drill 8-mm. 14б. To disconnect the top case 9 from a flange of a casing 10 steering columns. 14в. To turn out cores of bolts 6 of the case 9 by means of flat-nose pliers. The prevention After operation of drilling of heads of bolts it is necessary to clear details of a shaving.

To establish or attach

Installation of the switch of ignition

12. THE CASE FOR FASTENING OF THE LOCK OF IGNITION 13. THE ADJUSTING SCREW 14. THE SWITCH OF THE LOCK OF IGNITION

---

The prevention

All fixing details used in operations described more low, should be densely wrapped before a definitive inhaling the moment of the demanded size.

---

PERFORMANCE ORDER

1. To connect the top case 9 to a flange of a casing 10 with the help срезных bolts 6. To tighten bolts and to cut off heads, having put a twisting moment about 15 Nanometers. The prevention To provide at installation coincidence of a uvula of the cylinder of the lock and a groove of the switch of ignition 14, it is necessary to turn preliminary them in position "RUN". 2. The switch of ignition 14 in the case 12. To be convinced that the pin has entered into an aperture of an eye of the switch 14. 3. To screw the adjusting screw 13 and to tighten it by hand (the moment about 0,3 Nanometers). 4. The cylinder of the lock of ignition in the case 12. 5. To attach the case 12 to the top case 9 steering columns by means of washers 8 and срезных bolts 7. To tighten bolts and to cut off heads, having put a twisting moment about 11 Nanometers. 6. To turn the cylinder of the lock of ignition in position "RUN". 7. A steering shaft 15 in a casing 10 through the bottom aperture. To advance a shaft against the stop. 8. To turn the cylinder of the lock of ignition in position "OFF-LOCK" and to take out a key. 9. To turn a steering shaft 15 before operation of the lock of blocking. 10. The case of 5 lever switches on the top case of 9 columns. To screw screws 4 and to tighten their moment of 3,4 Nanometers. 11. Directing plug 11 on the bottom end of a steering shaft 15 and in a casing 10. 12. A steering column in gathering on the car. The prevention After connection of a steering shaft with a shaft of the steering mechanism to take out directing plug 11 of a casing 10 and to leave it on the helmsman to a shaft 15 for use further. 13. A persistent washer 3 and a spring on the top end of a shaft 15. 14. A steering wheel on a shaft 15. To screw a nut 1 and to tighten its moment of 17 Nanometers.