Daewoo Nexia

Since 1994 of release

Repair and car operation

Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
- The engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance service and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation in gathering
   2.6. Engine support
   2.7. An inlet collector and a lining
   2.8. A final collector and a lining
   2.9. A cover of the case of a cam-shaft
   2.10. A pulley of a cranked shaft
   2.11. A forward cover of a gear belt
   2.12. A camshaft cogwheel
   2.13. A cogwheel of a cranked shaft
   2.14. A back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Check of angular position of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. A camshaft. Levers. Hydrojacks of backlashes
   2.19. Klapannye springs. Consolidations of cores of valves
   2.20. A head of cylinders. The camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of apertures of plugs
   2.25. Valves
   2.26. Klapannye springs
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of backlashes
   2.31. The oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. The oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. A flywheel. Back consolidation of a cranked shaft
   2.37. A cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. The block of cylinders
   2.43. Installation of pistons
   2.44. Balancing of a disk with a gear wreath
   2.45. Repair of carving apertures
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

2.29. Height of a core of the valve concerning a head of the block of cylinders

THE GENERAL DATA

Measurement of height of a core of the valve with the help скобы

1. THE MINIMUM BACKLASH BETWEEN СКОБОЙ AND THE TIP OF THE CORE OF THE VALVE IS EQUAL 0,38 MM (FLAT ЩУП IN THE THICKNESS 0,38 MM IS AVAILABLE IN REPAIR COMPLETE SET ВТ-3005 OF THE CARBURETTOR)
2. MEASURING СКОБА
3. PLACES OF OPIRANIJA СКОБЫ ON THE HEAD OF THE BLOCK OF CYLINDERS SHOULD BE SMOOTH AND PURE

The height of a core of the valve should not surpass certain value, fig. Measurement of height of a core of the valve with the help скобы see. For measurement of height of a core of the valve it is necessary to use adaptation DT12003 (measuring скоба). If the distance from an end face of a core of the valve to скобы is great, it is necessary in addition прошлифовать valve and saddle facets. If the valve height exceeds the admissible size, it is necessary to replace a head of the block of cylinders with saddles.
The prevention
It is forbidden to shorten a core of the valve grinding of a tip of a core.