Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
- The engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance service and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation in gathering
   2.6. Engine support
   2.7. An inlet collector and a lining
   2.8. A final collector and a lining
   2.9. A cover of the case of a cam-shaft
   2.10. A pulley of a cranked shaft
   2.11. A forward cover of a gear belt
   2.12. A camshaft cogwheel
   2.13. A cogwheel of a cranked shaft
   2.14. A back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Check of angular position of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. A camshaft. Levers. Hydrojacks of backlashes
   2.19. Klapannye springs. Consolidations of cores of valves
   2.20. A head of cylinders. The camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of apertures of plugs
   2.25. Valves
   2.26. Klapannye springs
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of backlashes
   2.31. The oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. The oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. A flywheel. Back consolidation of a cranked shaft
   2.37. A cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. The block of cylinders
   2.43. Installation of pistons
   2.44. Balancing of a disk with a gear wreath
   2.45. Repair of carving apertures
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment



2.15. Adjustment of a tension of a gear belt
THE GENERAL DATA

Installation of a cranked shaft on a label on a pulley

43. THE BOLT OF FASTENING OF THE COGWHEEL
44. THE GEAR BELT

AND. THE LABEL ON THE PULLEY OF THE CRANKED SHAFT
CENTURY THE INDEX ON THE BACK COVER OF THE GEAR BELT

   

Adjustment натяжителя a belt

 


To adjust

PERFORMANCE ORDER
1. To remove приводные belts, the conditioner compressor, the pump of the steering amplifier, the generator.
2. Pipelines of the pump of the steering amplifier.
3. To turn a cranked shaft for a head of a bolt of a cogwheel that the piston of the first cylinder was established in position 10 "to ВМТ. The label on a pulley of a cranked shaft should coincide with the index on a back cover of a gear belt (Installation of a cranked shaft on a label fig. see a pulley).
4. To remove bolts and a forward cover of a gear belt.
5. To adjust a tension of a gear belt in the following sequence.
5а. To remove three bolts of 151 fastenings of the water pump.
5б. To expose the adjusting lever on the aperture centre in an arm, as is shown in fig. Adjustment натяжителя a belt. Slightly to tighten three bolts of fastening of the water pump.
The prevention

For fixing from arm and lever rotation to insert into an aperture a screw-driver.


5в. For correct installation of details to turn a cranked shaft on two turns (to remove three bolts of fastening of the water pump).
5г. To turn the case of the water pump counter-clockwise, keeping the lever index on an arm label.
5д. To tighten bolts of fastening of the water pump the moment of 20-30 Nanometers.