Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


1cb365f7

3.37. A cranked shaft To remove or disconnect

PERFORMANCE ORDER
1. The engine.
2. To merge oil.
3. To establish the Engine on the stand.
4. To unscrew spark plugs 6.
5. A pulley 157 with a nave.
6. A cover 73 gear belts.
7. A gear belt 62, having weakened bolts of fastening of the water pump.
8. A flywheel 126.
9. The oil pallet 134.
10. A cogwheel 153 cranked shaft.
11. A back cover 52 gear belts.
12. The oil pump 147.
13. Covers of 172 rods with loose leaves, preliminary having marked.
14. Pistons 175 with rods.
15. Covers of 131 radical bearings with loose leaves 129 and 130. Preliminary to mark details.
16. A cranked shaft 128.

To clear and check up

Look subsection 2.37.

To establish or attach

PERFORMANCE ORDER
1. New top loose leaves 129, 130, a cranked shaft 128.
2. Covers of 131 radical bearings with new loose leaves 129, 130. Not to tighten bolts 132. Preliminary to oil loose leaves.
3. To establish in cylinders pistons 175 with rods and new loose leaves 173.
4. Covers of 172 rods with new the loose leaf ми 173. Not to tighten шатунные bolts 171.
5. Blows of a hammer with rubber brisk on the ends of a cranked shaft to centre persistent bearings 130.
6. To tighten bolts of fastening of covers of 132 radical bearings. To tighten bolts of fastening of covers of radical bearings the moment of 50 Nanometers, then in addition to tighten turn нa 45 –60 . To check up an axial backlash of a cranked shaft. It should be within 0,07 – 0,30 mm.
7. To tighten bolts of 171 covers 172 шатунных bearings. To tighten bolts of fastening of covers шатунных bearings the moment of 25 Nanometers, then in addition to tighten turn on 30 .
8. To measure lateral backlashes of all rods. Backlashes should be within 0,07–0,242 mm.
9. The oil pump 147.
10. New forward consolidation of a cranked shaft, using the assembly adaptation.
11. A back cover 52 gear belts.
12. A cogwheel 153.
13. The oil pallet 134.
14. New back consolidation 127 by means of the assembly adaptation.
15. A flywheel. To tighten bolts of a flywheel the moment of 35 Nanometers, then in addition to tighten turn on 30 –45 .
16. A gear belt and a cover.
17. A pulley of a cranked shaft. To tighten bolts of fastening of a pulley of a cranked shaft the moment of 55 Nanometers.
18. Spark plugs.
19. To establish the Engine on the car.
20. To fill in engine oil.