Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


1cb365f7

3.10. An inlet collector and a lining
THE GENERAL DATA

Branch pipe of an air cleaner and electric sockets

 


Vacuum hoses

 


The case throttle заслонки

 


Arm of an inlet collector

 


Dismantle of an inlet collector with a lining

 


Sequence of an inhaling of bolts and nuts of fastening of an inlet collector

 

To remove or disconnect

PERFORMANCE ORDER
1. The bottom hose of a radiator and a negative wire of the battery.
2. A collar and an air branch pipe of an air cleaner from the case throttle заслонки.
3. Ventilating hoses In and With.
4. Electric socket D of the air valve of idling and socket Е of the gauge of position throttle заслонки, located on the case 97 throttle заслонки. A cable of 101 managements throttle заслонкой and an arm of 99 fastenings of a cover of a cable.
5. A belt of the generator and a bolt of a lath of the generator.
6. Hose G of a drain tank, a hose of a supply of a cooling liquid from corresponding branch pipes on the case throttle заслонки.
7. A vacuum hose of I regulator of pressure of fuel, a hose To the conditioner, hose J of the brake amplifier, hose L of the gauge of absolute pressure and "a mass" wire of M ECU.
8. An arm 76 inlet collectors, bolts 77, 78.
9. An inlet collector 92 with a lining 91, seven bolts 95 and two nuts 94. Сопрягае мые planes of a head of cylinders and an inlet collector.

To establish or attach

PERFORMANCE ORDER
1. An inlet collector 92 with a new lining 91 (fig. Sequence of an inhaling of bolts and nuts of fastening of an inlet collector see).
2. Nuts 94 and bolts 95. To tighten nuts and bolts of fastening of an inlet collector the moment of 25 Nanometers in the sequence shown on fig. Sequence of an inhaling of bolts and nuts of fastening of an inlet collector.
3. An arm 76 inlet collectors, the top bolts 77, the bottom bolt 78. To tighten the top bolts 77 moment of 25 Nanometers, and the bottom bolt 78 moment of 40 Nanometers.
4. A vacuum hose of I regulator of pressure of fuel, a hose To the conditioner, hose J of the brake amplifier, hose L of the gauge of absolute pressure and "a mass" wire of M ECU.
5. Hose G of a drain tank, hose Н of a supply of a cooling liquid to the case throttle заслонки.
6. To Planck of the generator on an inlet collector.
7. A privodnoj belt of the generator and to adjust a belt tension.
8. An arm of 99 fastenings of a cover of a cable and a cable of 101 managements throttle заслонкой. Electric socket D of the air valve of idling and socket Е of the gauge of position throttle заслонки, located on the case 97 throttle заслонки.
9. Ventilating hoses With and In to branch pipes on a cover клапанного the mechanism, the case throttle заслонки and a collector воздухочистителя.
10. An air branch pipe of an air cleaner to the case throttle заслонки to establish a collar.
11. To fill system of cooling with a cooling liquid. If necessary to remove air from system.
12. A negative wire of the storage battery.