Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment



3.24. Klapannye springs. Consolidations of cores of valves
THE GENERAL DATA

Compression клапанных springs by means of a stripper

 


Dismantle of consolidations of cores of valves

 


Consolidation of a core of the valve and assembly оправка

 


Installation of consolidations of cores of valves

 


Installation of crackers of valves


 


To remove or disconnect

PERFORMANCE ORDER
1. A head of cylinders 33.
2. To mark all valves that at the subsequent assemblage to keep their arrangement.
3. Crackers 22, using for compression клапанных springs stripper КМ-348.
4. Plates 21 клапанных springs, клапанные springs 23 and valves 34. In avoidance травмирования it is necessary to show care at release compressed клапанных springs.
The prevention

All removed details should be put as their dismantle to facilitate the subsequent assemblage.


5. Consolidations of 24 cores of valves.
The prevention

24 it is necessary to replace the dismantled consolidations with the new.


6. To clear a deposit by means of a soft brush.
The prevention

It is necessary to blow and dry oil channels and directing plugs the compressed cleared air.



To establish or attach
The prevention

Before assemblage to clear all details. For greasing of mobile and rotating details to use pure engine oil.


PERFORMANCE ORDER
1. Plates клапанных springs and new consolidations of 24 valves by means of the assembly adaptation.
2. To insert consolidation 24 in оправку. Напрессовать consolidation on I direct щую the valve plug against the stop blows of a wooden hammer on оправке.
3. To grease cores of valves with engine oil and to establish them in plugs.
The prevention

To check up smoothness of movings of valves in directing plugs.


4. Klapannye springs 23 and plates of springs 21.
5. To compress клапанные springs stripper КМ-348 and to establish crackers 22.
6. A head of the block of cylinders.