Daewoo Nexia

Since 1994 of release

Repair and car operation


Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
- 10. A five-speed transmission and the main transfer RPO MM5
   10.2. The general description
   10.3. Diagnostics of malfunctions
   10.4. The possible reasons of the raised noise of a transmission
   10.5. Level check трансмиссионного oils
   10.6. Adjustment of a drive of the mechanism of switching
   10.7. The gear change lever
   10.8. The floor mechanism of management of a transmission
   10.9. Draught of the mechanism of management
   10.10. The intermediate lever
   10.11. A speedometer drive
   10.12. A cover of the mechanism of the switch
   10.13. Consolidations of semiaxes
   10.14. Transmissions in gathering
   10.15. Dismantling of a transmission and the main transfer
   10.16. Characteristic malfunctions of a transmission and the possible reasons
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


1cb365f7

10.6. Adjustment of a drive of the mechanism of switching
THE GENERAL DATA

Bolt arrangement клеммового connections

210. BOLT КЛЕММОВОГО OF CONNECTION
239. THE LEVER AXIS

Arrangement of a stopper of an adjusting aperture

AND. THE STOPPER

224. THE PLATEN WITH THE PLUG

Installation of a cover of the lever of switching

AND. THE CONTROL PANEL OVERLAY
CENTURY THE COVER
WITH. THE SCREW
D. THE OVERLAY OF THE CENTRAL CONSOLE

Position of the lever of switching at drive adjustment

AND. THE ARROW
CENTURY THE LABEL

Measurement of an adjusting backlash

AND. THE DOGGIE
CENTURY THE EMPHASIS
WITH. THE BACKLASH
D. THE ADJUSTING NUT

PERFORMANCE ORDER
1. To disconnect a negative wire of the battery.
2. To translate the lever of switching 203 in neutral position.
3. To weaken a bolt 210 клеммового connections.
4. To turn out a stopper from an adjusting aperture in a cover 235 mechanisms of the switch. To turn a plug 224 so that through an adjusting aperture to insert small beards in diameter of 4,76 mm into an aperture of the intermediate lever of the switch 227.
5. To remove a cover 202 and to turn away it upwards, to open access to the mechanism.
6. To translate the lever of switching 203 in position of 1st or 2nd transfer.
6а. To achieve coincidence of an arrow to a label and to tighten a bolt 210.
6б. To tighten a bolt the moment of 14 Nanometers.
6в. After an inhaling the specified moment in addition to tighten a bolt turn on 90–180 degrees.
7. To translate the switching lever in neutral position and to check up backlash size between the doggie And and V.Posle's emphasis of adjustment a backlash it should be equal 3 mm.
8. To take out from apertures of small beards in diameter of 4,76 mm and to establish into place a stopper.
9. To adjust by means of nut D a backlash With, as is shown in fig. Measurement of an adjusting backlash. Before adjustment to unbend two pads of a clamp of a nut.
9а. The backlash should be equal 11,6 0,2 mm.
9б. To fix pads регулировоч ную a nut from отворачивания.
10. To establish into place a cover 202 and an overlay of the central console.
The prevention

All transfers should join easily on the motionless car with the idling engine and the switched off coupling.