Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral молдинги
   18.4. Diagnostics and repair негерметичности Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination негерметичности consolidations
   + 18.12. A rear-view mirror
   - 18.13. An electroheater of back glass
      18.13.1. Check of serviceability of electrospending strips of a heater
      18.13.2. Repair of electrospending strips of a heater
      18.13.3. Repair of a feeding wire
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. Вентиляционнай the valve (the Body a hatch-back)
   18.35. Лючок mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment



18.13.2. Repair of electrospending strips of a heater
THE GENERAL DATA

Repair of electrospending strips of a heater

1. THE STICKY TAPE
2. THE DAMAGED STRIP
3. THE WOODEN SHOVEL
4. THE REPAIR INSERT

PERFORMANCE ORDER
1. To disconnect a wire of a food from an electroheater of back glass.
2. To check up serviceability of electrospending strips of a heater.
3. To note places of damages of strips by means of a pencil-steklografa or it is small (on lateral aspect of back glass).
The prevention

To remove the damaged site of a strip at length about 6 mm from each party from rupture. To wipe the damaged place the pure fabric moistened with spirit.


4. To paste on the damaged place a repair sticky tape or two pieces of a usual sticky tape from above and from below from a repaired strip. The sticky tape is necessary for restriction of width of a repair zone.
At use of a special repair tape it is necessary to be convinced that the width of a cut in it corresponds to width of a repaired electrospending strip. To uncover boxes in which materials for repair of electrospending strips are stored.
5. Carefully to mix a hardener with the basic structure of silvery colour. In case of hardener crystallisation it is necessary to ship packing with it in hot water and to wait, while the hardener again becomes liquid.
6. At a room temperature to put on the damaged place a repair composition by means of a small wooden stick or a shovel.
7. Cautiously to remove protective sticky tapes.
The prevention

Polymerisation of a repair composition should occur in heat. In order to avoid damage of an upholstery of salon from a source it is warm it is necessary to establish filters. To heat up the damaged place within 1–2 minutes. A heating element it is necessary to have on distance of 25 mm from the damaged place. Is minimum necessary temperature of heating makes 149 With.


8. To check up the repaired place of an electrospending strip. If the strip has become colourless, it is necessary to put нa it by means of a brush тонирующий structure. After подсыхания during 30 with to wipe a pure not fleecy fabric surpluses тонирующего structure. To include and check up work of an electroheater of back glass.
The prevention

Full of polymerisation of a repair composition proceeds not less than 24 hours. During this time it is necessary to exclude mechanical influence on the repaired place of a strip.