Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral молдинги
   18.4. Diagnostics and repair негерметичности Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination негерметичности consolidations
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. Вентиляционнай the valve (the Body a hatch-back)
   18.35. Лючок mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment


1cb365f7

18.2. Identification and use of keys
THE GENERAL DATA

The sizes of a small beard of a key


Uvula of a key with a code


For the lock of ignition, locks of doors and a luggage carrier cover the same key is used. The key has a bilaterial symmetric small beard which allows to insert a key into the lock cylinder in any position. The code is put on an auxiliary plate of a key which leaves further. At key manufacturing необходи мо to define a code by means of the scheme resulted on fig. the Sizes of a small beard of a key.

Replacement of the cylinder of the lock

The cylinder of the lock of ignition

1. NESTS OF SPRINGS ЗАПОРНЫХ OF PLATES
2. ЗАПОРНАЯ THE PLATE

Zapornye plates for all cylinders have absolutely identical form except for a through cut. Использу ется four standard sizes запорных plates which provide reception of various confidential combinations. Everyone запорная a plate has marks in figure from 1 to 4. The key small beard simultaneously co-operates with 10 запорными plates.

Depending on a combination of standard sizes of the complete set established in the cylinder запорных plates the key small beard has this or that profile, fig. the Sizes of a small beard of a key.

PERFORMANCE ORDER
1. To define numbers of standard sizes запорных plates, measuring the cross-section size of the cylinder of the lock in planes of an arrangement of plates (with 1st on 10th) by means of shtangen-compasses. To write down results of measurements.
2. Since the first position to insert springs of plates and запорные plates into corresponding apertures and cuts of the cylinder of the lock. Thus it is necessary to be guided by a key code. In the cylinder of the lock of ignition it is used 10 запорных plates.
The prevention

At installation of springs and запорных plates in the lock cylinder it is necessary to grease to a wasp of a detail with a thin layer консистентной greasings.



Assemblage of the lock of ignition


The ignition lock

1. THE DIRECTING ELEMENT
2. THE LOCK CYLINDER
3. THE LOCK CASE

PERFORMANCE ORDER
1. To grease консистентной with greasing directing element and a spring and to insert them into a nest of the cylinder of the lock. To level position запорных plates, having inserted into the cylinder the ignition key.
2. To grease консистентной with greasing an internal surface of an aperture of the case of the lock and to insert into it the cylinder.
3. To establish a spring and a finger of a steering column, preliminary having greased them консистен тной with greasing.