Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral молдинги
   18.4. Diagnostics and repair негерметичности Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   - 18.11. Elimination негерметичности consolidations
      18.11.2. Clearing
      18.11.3. Installation or joining
      18.11.4. Check
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. Вентиляционнай the valve (the Body a hatch-back)
   18.35. Лючок mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment


1cb365f7

18.11. Elimination негерметичности consolidations
THE GENERAL DATA

Repair of not tight consolidation

AND. EXISTING LAYER ГЕРМЕТИЗИРУЮЩЕГО OF STRUCTURE
CENTURY REMOVAL OF EXTERNAL LAYER ГЕРМЕТИЗИРУЮЩЕГО OF STRUCTURE
WITH. PRIMING COAT DRAWING
D. DRAWING OF REPAIR LAYER ГЕРМЕТИЗИРУЮЩЕГО OF STRUCTURE
Е. THE FLAT SHOVEL
F. TO DISTRIBUTE AND PRESS ГЕРМЕТИЗИРУЮЩИЙ STRUCTURE INTO CRACKS

In certain cases негерметичность consolidations can be eliminated without dismantle and the subsequent installation of glasses. This way of repair is applicable only to the glasses established on уретановый герметизирующий structure, and demands application of materials from a repair glutinous set.

PERFORMANCE ORDER
1. To remove молдинг, closing a leak place. In certain cases dismantle of additional details can be demanded to localise a leak place.
2. To note not tight place. Cautiously to press from within glass, to specify extent of defect of consolidation. At this time glass should be watered outside. To note extent of the damaged place.
3. To wash out water a zone adjoining to not tight place, from a dirt and extraneous substances. Then to dry a current of air.
4. By means of a sharp knife to remove from a defective place герметизирующий structure at length of 75-100 mm (from both parties).
5. To put on the damaged place a priming coat, using materials from a repair set. Before use it is necessary to mix packing contents. To dry within 5 minutes.
6. To put from two parties герметизирующий structure on the damaged place (at length of 75-100 mm).
7. At once after drawing to distribute and press герметизирующий structure into cracks between glass and a framework of a window aperture for maintenance of tightness of connection. To use for this purpose a flat shovel or other suitable tool.
8. By means of a stream of warm or hot water to check up tightness of consolidation. It is not necessary to direct a strong stream of water on свеженанесенный герметизирующий structure.
9. To establish into place all preliminary dismantled details.