Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral молдинги
   18.4. Diagnostics and repair негерметичности Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination негерметичности consolidations
   + 18.12. A rear-view mirror
   - 18.13. An electroheater of back glass
      18.13.1. Check of serviceability of electrospending strips of a heater
      18.13.2. Repair of electrospending strips of a heater
      18.13.3. Repair of a feeding wire
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. Вентиляционнай the valve (the Body a hatch-back)
   18.35. Лючок mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment



18.13.1. Check of serviceability of electrospending strips of a heater
THE GENERAL DATA

Check of serviceability of electrospending strips of a heater

1. THE VOLTMETER

For detection of the damaged electrospending strips it is necessary to start the Engine and to include an electroheater. By means of the voltmeter serially to measure pressure on all strips, having attached one sampler to "weight", and another – to strips about the left and right tyres. If the size of pressure measured on both ends of each strip, is approximately equal to pressure of the storage battery, it is necessary to check up reliability of contact of a "mass" wire with a car Body.

Pressure on a strip should decrease in process of removal of a sampler from the tyre of a food of an electroheater of back glass. Each strip should be checked up at least in two places to exclude probability of the admission of the damaged place. It is recommended to make check of serviceability of strips in two places located on identical distances from the central line of back glass. At detection of abnormal indications of the voltmeter on one of strips it is necessary to move a sampler along this strip until pressure does not become equal to zero. In this place there is a strip rupture.