Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
- 14. A forward suspension bracket
   14.2. The general description
   14.3. Check of size of forces of a friction in a suspension bracket
   14.4. Condition check подшипниковых support and spherical hinges
   14.5. The stabilizer
   14.6. A rack in gathering with подшипниковой a support
   14.7. The bottom lever
   14.8. The spherical hinge
   14.9. A nave and the wheel bearing
   14.10. The top support
   14.11. Springs
   14.12. The shock-absorber
   14.13. Plugs of hinges of the bottom lever
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


1cb365f7

14.6. A rack in gathering with подшипниковой a support
THE GENERAL DATA

Fastening of a telescopic rack to the Body

36. THE PROTECTIVE COVER OF THE TOP SUPPORT
37. THE NUT (THE MOMENT OF THE INHALING OF 30 NANOMETERS)
39. TOP (ПОДШИПНИКОВАЯ) THE RACK SUPPORT

Spring clamp

AND. THE BACK HANDLE
CENTURY FORWARD LOOPS
WITH. CLAMPS

1. THE SPRING CLAMP

To remove or disconnect

Dismantle of the hinge of steering draught


33. THE RACK WITH ПОДШИПНИКОВОЙ THE SUPPORT
59. THE TIP OF STEERING DRAUGHT

Dismantle of the spherical hinge of the bottom lever

6. THE SPHERICAL HINGE OF THE BOTTOM LEVER
13. THE BOTTOM LEVER
57. СКОБА THE DISK BRAKE

Dismantle of a semiaxis from a nave

AND. THE NUT
CENTURY THE BOLT
WITH. THE PERSISTENT BEARING

33. THE RACK WITH ПОДШИПНИКОВОЙ THE SUPPORT

PERFORMANCE ORDER
1. To release two nuts of 37 fastenings of the top support of a rack.
2. To release bolts of fastening of forward wheels. To take out шплинт 54, to turn away a nut of 55 semiaxes and to remove a washer 53.
3. To lift the car.
4. To bring basic racks under the car.
5. To lower it is a little car so that he leant against racks, but not on the bottom levers.
6. Forward wheels.
The prevention

To track in order that after dismantle of nuts of a semiaxis did not leave internal mobile hinges. It will lead to dismantling of hinges. Probably also damage of hinges. During work in a zone of an arrangement of hinges of semiaxes it is necessary to use the protective covers which are put on on rubber грязезащитные of consolidation of hinges. Otherwise damage of details or consolidations of hinges and an exit of hinges out of operation is possible.


7. Скобу 57 brakes from подшипниковой support. After dismantle follows зафиксиро вать скобу not to damage brake hoses.
8. The screw 56.
9. A brake disk 52.
10. Nuts of spherical hinges of rotary levers.
The prevention

For dismantle of external spherical hinges of a steering trapeze use stripper КМ-507В.


11. A spring clamp of 1 nut 2.
11а. To raise the back handle of a clamp and to take out it for forward loops.
12. To turn away a nut 2.
13. By means of stripper КМ-507В to take out a finger of the spherical hinge from an arm aperture подшипниковой support.
The prevention

At use of stripper КМ-507В for dismantle of spherical hinges it is not necessary to pay attention to an inscription "This party to a wheel", выштампованную on the adaptation.


14. To disconnect полуось from a nave.
15. To fix полуось.
16. To lower the car to turn on and remove two nuts 37 with washers 38.
17. A telescopic rack 33 in gathering.
The prevention

At dismantle and the further works with springs of racks not to suppose having chopped off or scratches of a covering of coils of springs.



To establish or attach

PERFORMANCE ORDER
1. A telescopic rack 33 in gathering and two nuts of 37 fastenings of a rack to the Body.
2. To tighten nuts of fastening of a rack to the Body the moment of 25 Nanometers.
3. To remove the protective covers which have been put on on rubber грязезащитные of consolidation of hinges.
4. To insert a semiaxis shaft in шлицевое an aperture of a nave 51. To establish a washer 53 and to screw a new nut 55. Before assemblage to check up greasing presence in semiaxis hinges. If necessary to add corresponding greasing. Not to tighten a nut 55 before installation of a wheel and car lowering on a floor.
5. The spherical hinge on подшипниковую a support and a nut 2. To tighten a nut of fastening of the spherical hinge the moment of 70 Nanometers.
6. A spring clamp 1.
7. The spherical hinge of steering bent for to the lever of a rack 33. To tighten a nut of fastening of the spherical hinge of steering bent for to the lever of a rack the moment of 60 Nanometers.
8. A brake disk 52 and the screw 56. To tighten the screw of fastening of a disk to a nave the moment of 4 Nanometers.
9. Скобу 57 disk brakes on a rack 33.
10. A wheel.
11. To raise it is a little car.
12. To remove basic racks.
13. To lower the car.
14. To tighten bolts of fastening of a wheel in a cross order the moment of 90 Nanometers.
15. To tighten корончатую a nut of 55 fastenings of a semiaxis the moment of 100 Nanometers. (To use a new nut).
16. To release a nut 55 and then definitively to tighten its moment of 20 Nanometers.
17. At discrepancy of a cut of a nut with an aperture in a shaft of a semiaxis for шплинта a few to turn away a nut 55 and again to tighten the specified moment. It is forbidden to increase the moment of an inhaling for maintenance of coincidence of a cut of a nut with an aperture for installation шплинта 54.