Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral молдинги
   18.4. Diagnostics and repair негерметичности Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination негерметичности consolidations
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. Вентиляционнай the valve (the Body a hatch-back)
   18.35. Лючок mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   - 18.49. The ventilating hatch
      18.49.1. A sharnirnaja loop
      18.49.2. The glass panel
      18.49.3. A fringing
      18.49.4. A hatch lock
      18.49.5. A sealant
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment



18.49.5. A sealant
THE GENERAL DATA

The hatch sealant represents closed профилированное a ring. The sealant is established in a groove on aperture perimetre on glue.

To remove or disconnect

PERFORMANCE ORDER
1. The glass panel from a hatch framework.
2. To cut off glutinous connection of a sealant on perimetre of a groove and to dismantle consolidation.
The prevention

For acceleration of dismantle of consolidation it is recommended to heat up consolidation by a stream of hot air or to moisten glutinous connection by solvent for glue.


3. After consolidation removal to clear a groove of the rests of glue by means of solvent.

To establish or attach

PERFORMANCE ORDER
1. To paste a protective tape on perimetre of an aperture of the hatch.
2. To put a layer of glue of mark 3М Windo-Weid Primer (black colour) on horizontal and vertical surfaces of a groove. To allow to glue to dry up within 10–15 minutes.
3. To clear. A surface of consolidation by means of suitable solvent.
4. To grease contact surfaces with a layer of glue of mark 3М Windo-Weid Primer (black colour) and to allow to glue to dry up within 10–15 minutes.
5. Being guided by a cross-section seam of a sealant, to put a label a sticky tape in the middle of an opposite side. Condense тель it is necessary to mount so that the cross-section seam was in the middle of the back party of an aperture. To put a glue layer 3М Weatheistrip Adhesive on surfaces of a groove for consolidation installation on internal perimetre of an aperture of the hatch.
6. By means of a brush to put glue on contact surfaces of consolidation.
7. After glue becomes sticky, to level sealant position on a seam and labels from a sticky tape and to insert a sealant into a groove. The cross-section seam should be in the middle of the back party of an aperture over the handle of a lock of the hatch.
8. By means of a syringe to put a glue layer between an outer side of consolidation and aperture edge in a roof.
9. To allow to dry out to glue within 8 hours before to mount the hatch and to check a sealant on tightness. Before installation of the glass hatch to put on a sealant silicone greasing.
10. To establish the glass panel on a hatch framework.