Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
- 16. A back suspension bracket
   16.2. The general description
   16.3. Maintenance service and repair
   16.4. Check of size of forces of a friction in a suspension bracket
   16.5. Bearings of wheels
   16.6. The shock-absorber
   16.7. The stabilizer
   16.8. Springs
   16.9. Plugs of hinges of a back suspension bracket
   16.10. A back suspension bracket in gathering
   16.11. A nave
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment



16.10. A back suspension bracket in gathering To remove or disconnect

PERFORMANCE ORDER
1. To lift the car and to remove back wheels.
2. The teplootrazhatelnyj screen of system of release of the fulfilled gases from the car bottom.
3. To measure free length of a carving tip of draught of a lay brake.
3а. A self-stopped nut from draught of a lay brake.
3б. A lock plate from the equalizer lever.
3в. A cable of a drive of a lay brake from the equalizer lever.
3г. A cable of a drive of a lay brake from directing, located on трансмиссионном the tunnel.
3д. To disconnect plastic plugs from a hook on a fuel tank and to take aside the muffler.
4. To bring a hydraulic jack with a suitable support under one of levers back to bring and a little to raise it.
5. To disconnect pipelines of a brake drive from brake hoses at support вающих arms and to remove clamps.
5а. To disconnect brake hoses from an arm.
5б. To put on caps or to muffle stoppers of an aperture of pipelines in order to avoid dirt hit.
6. Shock-absorbers.
7. Bolts 23 from hinges of levers of a back suspension bracket. To lower a hydraulic jack.
8. Springs 28 back suspension brackets. If necessary to wring out the lever downwards, having inserted into an arm of the shock-absorber the lever, and to remove a spring 28. In a similar order to dismantle a spring 28 and the shock-absorber 7 on other party of the car.
9. To substitute a hydraulic jack under the middle of a beam of a back suspension bracket.
9а. A bolt 23 from an arm on the Body bottom.
9б. To lower a jack with a beam of a back suspension bracket. To place a cable of a lay brake on the muffler.
9в. To remove a beam of a back suspension bracket from a jack (together), to establish and clamp it in a vice, using safety linings.

To disassemble

PERFORMANCE ORDER
1. To turn out the lock screw and to remove a brake drum. If necessary to take away back by means of a screw-driver разжимной the lever of a lay brake.
2. To take out a protective cap 17 of a nave 12.
3. To take out шплинт 15 and to turn away a nut of 16 pins.
3а. To dismantle a nave 12 from a pin.
4. To unbend collars of fastening of cables of the lay brake, located on a back suspension bracket.
5. To turn away bolts and to remove basic brake disks from levers of a back suspension bracket. To remove cardboard linings.
6. To turn away bolts of fastening and to dismantle the stabilizer 25. If necessary to weaken stabilizer landing in nests to use выколотку.
7. To disconnect cables of a drive of a lay brake from fastenings on levers of a back suspension bracket.

To collect

PERFORMANCE ORDER
1. To insert the stabilizer 25 into a new beam of a back suspension bracket and bolts in apertures of heads of the stabilizer. To screw nuts and to tighten bolts the moment of 80 Nanometers.
2. To cover the back party of a basic brake disk contacting to a cardboard lining, a thin layer of hermetic. To establish into place a cardboard lining.
3. To grease fixing bolts with a thin layer of fixing structure and to fix basic brake disks on suspension bracket levers. To tighten bolts the moment of 28 Nanometers.
4. To attach drive cables стояночно го brakes to fastenings on levers of a back suspension bracket. To bend collars.
5. To grease a pin консистентной with greasing for bearings and to establish a nave 12. To fix a nave a lock washer 14 and a nut 16. To tighten a nut 16 moment of 16 Nanometers. To adjust nave bearings.
6. To establish brake drums and lock screws.

To establish or attach

PERFORMANCE ORDER
1. To establish (together) a beam of a back suspension bracket in gathering on a hydraulic jack. To place a cable of a drive of a lay brake on the muffler.
2. To lift a beam of a suspension bracket and to attach it to arms on the Body bottom.
2а. To substitute a hydraulic jack with a suitable support under one of levers and a few to raise it.
3. The bottom buffer of a spring 27, a spring 28 and the top elastic ring 29 in the Body glass.
4. In addition to raise a jack the lever of a suspension bracket and to insert an eye of the shock-absorber 7 into an arm.
4а. If apertures of an arm and a shock-absorber eye are not coaxial, to level them by means of a core.
4б. To insert a bolt 8, to screw a nut 9 and to tighten its moment of 69 Nanometers.
4в. To lower a jack.
5. To fix brake hoses in кронштей нах on a beam of a back suspension bracket, to establish collars. To connect pipelines of a brake drive to hoses.
6. To establish a cable of a lay brake in a hook on a fuel tank and in an arm on the Body bottom.
7. To attach to draught of a lay brake the equalizer, a cable and to screw a nut. The nut should be in the same position, as before dismantling (see operation 3 on dismantle of a beam of a back suspension bracket).
8. To lower it is a little car and to establish back wheels.
9. At the released lever of a lay brake to adjust nut position on draught of a lay brake so that slowly rotating back wheels started to be braked.
10. To adjust bearings of naves of wheels.
11. To lower the car and to tighten bolts of fastening of wheels the moment of 90 Nanometers.
12. In the static position of the suspension bracket corresponding to the equipped weight of the car to insert into arms bolts of 23 fastenings of hinges of levers of a suspension bracket, to screw nuts 21 and to tighten their moment of 95 Nanometers.
13. To adjust back brake mechanisms.
13а. To let the air out from a hydrodrive of brakes (to pump over hydrosystem).
13б. To check up tightness of hydrosystem.
13в. To adjust a lay brake.