Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
- 15. A drive of forward wheels
   15.2. The general description
   15.3. Kardannye shaft in gathering
   15.4. An external reflective ring
   15.5. A cover of the external hinge
   15.6. The external hinge
   15.7. A cover of the internal hinge of type "Tripod"
   15.8. A cover of the hinge of type "Lebro" with cross flutes
   15.9. Consolidation карданного a shaft in картере transmissions
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment



15.3. Kardannye shaft in gathering
THE GENERAL DATA

Fastening of the top support of a rack to the Body

101. NUTS of FASTENING of the TOP SUPPORT of the RACK. The MOMENT of the INHALING of 30 Nanometers.

The adaptation for a coupler of rings of the bearing

AND. EXTERNAL DIAMETER 40 MM
CENTURY INTERNAL DIAMETER 20 MM
501. THE BRAKE DISK
502. THE NUT
503. THE WASHER
504. THE BOLT IN LENGTH 100 MM

Spring ring


3. THE SEPARATOR
5. BALLS
6. THE SPRING RING
10. THE SHAFT

To remove or disconnect

Nut of fastening of a semiaxis in a nave

 

Dismantle of the spherical hinge from подшипниковой rack support

7. THE COLLAR
8. THE COVER
10. THE SHAFT

Dismantle of a finger of the spherical hinge from the rotary lever of a rack


Dismantle of a semiaxis from a wheel nave

AND. THE NUT
CENTURY THE BOLT
WITH. THE PERSISTENT BEARING

401. THE WHEEL NAVE

Dismantle карданного a shaft from картера transmissions

8. THE COVER
10. THE SHAFT

PERFORMANCE ORDER
1. To open a cowl and to weaken nuts of the top support of a spring rack of a suspension bracket.
2. A cap of a wheel and to weaken bolts of fastening of a wheel.
3. Шплинт, a nut of a semiaxis and a washer.
4. To lift the car and to remove a wheel.
5. A spring clamp and a nut of fastening of a finger of the spherical hinge of the lever.
6. The spherical hinge of the lever by means of stripper КМ-507В.
The prevention

At use of stripper КМ-507В for dismantle of spherical hinges it is not necessary to pay attention to an inscription "This party to a wheel", выштампованную on the adaptation.


7. A nut of fastening of a finger of the spherical hinge of steering draught.
8. The spherical hinge of steering draught by means of stripper КМ-507В.
9. To take out полуось from a wheel nave.
The prevention

After dismantle of a semiaxis from a nave карданный the shaft should not hang freely, keeping only on the internal hinge. It is necessary to fix the free end карданного a shaft.

To place under карданный a shaft the pallet for отекания greasings. After shaft dismantle to close заглушкой an aperture in картере transmissions to prevent вытекание oils and dirt hit in a cavity картера.


10. A kardannyj shaft in gathering.
The prevention

After considerable run of the car (about 80-100 thousand in km) it is necessary to replace left and right карданные shaft in gathering.

At assemblage it is necessary to replace a spring clamp of the spherical hinge of the bottom lever with the new.

To check up, that consolidation in an aperture картера transmissions and the wheel bearing were pure.



To establish or attach

PERFORMANCE ORDER
1. Cautiously to insert into an aperture картера transmissions an internal shaft карданного a shaft 10, not to damage consolidation. To pull for the case of the external hinge for check of correct position of a shaft карданного a shaft inserted in картер.
2. An external shaft карданного a shaft in an aperture of a nave of a wheel.
3. The spherical hinge of the bottom lever on подшипниковую a rack support.
4. The spherical hinge of steering draught on the rotary lever of a rack. To tighten a nut of fastening of the hinge of steering draught the moment of 60 Nanometers.
5. To screw a nut on a finger of the spherical hinge of the bottom lever. To tighten a nut of the spherical hinge of the bottom lever the moment of 70 Nanometers.
6. A washer and a nut on a semiaxis shaft, strongly without tightening. To use only a new nut.
7. A wheel, having fixed bolts. Bolts strongly not to tighten.
8. To lower the car on a floor.
9. To tighten bolts of fastening of a wheel the moment of 90 Nanometers.
10. To tighten a nut of fastening of a semiaxis originally the moment of 100 Nanometers, then to release a nut and repeatedly to tighten the moment of 20 Nanometers. Then definitively to tighten a nut, having turned it on 1/4 turns.
11. To tighten nuts of fastening of the top support of a rack to the Body the moment of 30 Nanometers.
12. To fix шплинтом a semiaxis nut.
13. A spring clamp of a nut of the spherical hinge of the lever.
14. To fix шплинтом a nut of the spherical hinge of steering draught (if it is provided).
15. To finish oil level in картере transmissions to norm.