Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
- 11. Automatic Transmission
11.2. The terms, the accepted reductions and abbreviations
11.3. The general description of transmission
11.4. The basic knots of a transmission
11.5. Methods of localisation of leaks of a working liquid
11.6. Check of level of a working liquid in transmission 4T40
11.7. Diagnostics of malfunctions of knots of transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
Transmission noise
• Noise of chain transfer – the howling or roaring noise, which level increases or decreases at change of frequency of rotation of country houses of the engine. Noise is absent at dispersal of the car with a small corner of opening ДЗ and in an engine operating time on a place at inclusion in a transmission of ranges D (Movement) or R (Backing).
• Noise of the main transfer – the rumble, which level depends on speed of movement of the car. The rumble is swept especially up at dispersal of the car with small degree of opening ДЗ and during movement накатом with the released pedal of an accelerator.
• Noise of planetary transfer – howling noise which is most strongly shown on 1st transfer and transfer of a backing and depends on speed of the car. Noise of planetary transfer can decrease or vanish at transmission switching on an adjacent higher step.
• pump Noise – the howling sound of a high-pitch tone increasing with growth of turns of the engine. Pump noise can be audible on all transfers.
• hydrotransformer Noise – howling noise which is usually audible only on the motionless car at inclusion in a transmission of ranges D (Movement) or R (Backing). Noise ГТ increases with growth of turns of the engine.
High or low pressure of a working liquid in the trunk main
It is checked with the help плотномера (all switchings occur roughly or too slowly).
Possible codes of malfunctions:
– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – an unstable or chaotic signal
– 712 Gauge of temperature of a working liquid of transmission – a signal low voltage
– 713 Gauge of temperature the worker of a liquid of transmission – a signal high voltage
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 748 ЭМК a pressure regulator – refusal of an electric chain
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 1560 Deviation of pressure of an electric network from norm
– 1810 Malfunction of the switch of the control of ranges (the block of the relay of pressure)
– 1871 Wrong transfer number
– 1887 Relays of pressure of a friction clutch of blocking ГТ
TO CHECK UP | THE REASON |
Level of a working liquid | Too high or low level to finish level of a working liquid to norm |
The valve of a regulator of pressure, spring and бустерный the valve
| Valve jamming |
ЭМК a pressure regulator | Liquid leak, damage of sealing rings |
Easing of fastening of a socket, damage of pins |
Pollution |
The regulator valve on loading (twisting moment) of the engine | Valve jamming |
Transmission electroconducting | Easing of fastening of a socket, short circuit |
The block of the relay of pressure | Easing of fastening of a socket |
Damage or absence of sealing rings |
The filter of a working liquid | Contamination or damage of a filtering element, easing of fastening of the filter |
– Filter consolidation | Leak of a working liquid |
Heat exchanger pipelines | Забивание section through passage or deformation of pipelines |
The hydropump | Breakage, jamming, porosity of the case or leak |
Shaft of a drive of the hydropump | Breakage |
Safety valve | Spring breakage, absence of a ball |
Carter of transmission, the control panel transmission, the distributive panel | Porosity картера, leaks from a highway |
Infringement of planeness of interfaced surfaces |
Infringement of accuracy or sequence of the moments of switching
Possible code of malfunction:
– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – неустой чивый or a chaotic signal
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
–756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 1560 Deviation of pressure of an electric network from norms
TO CHECK UP
|
THE REASON
|
ЭМК switches
|
Pollution
|
Unstable rupture or chain short circuit
|
The gauge of position throttle заслонки
|
Breakage or detachment
|
Unstable rupture or chain short circuit
|
Gauges of speed of the car and speed of rotation of an entrance shaft
|
Breakage, detachment or fastening easing
|
Unstable rupture or chain short circuit
|
Rough gear change
TO CHECK UP
|
THE REASON
|
Pressure in the trunk main
|
High pressure of a working liquid
|
Ball return valves
|
Absence, is not present an inclusion delay
|
Демпферы inclusions of transfers
|
Piston or spring jamming, демпфер does not operate
|
Valve jamming демпфера
|
Stopper of the case and the ball valve in gathering
|
Закупоривание
|
Backing transfer, slipping of frictional knots on backing transfer does not join
TO CHECK UP | THE REASON |
Friction clutch of transfers of a forward course
|
Absence of inclusion, friction clutch slipping
|
– The piston in gathering with consolidation
|
Jamming, presence of cracks, leaks of a working liquid
|
– Internal consolidation
|
Zakuporivanie apertures
|
– Friction clutch disks
|
Deterioration of overlays, breakage шлицевых teeths
|
– A spring ring
|
Displacement from normal position
|
– The case
|
Presence of cracks, закупоривание highways
|
– A stopper of the case and the ball valve in gathering
|
Absence or displacement from normal position
|
– A spring
|
Jamming
|
Highways of a supply of a working liquid in a piston cavity of a friction clutch
|
Leak of a liquid or high resistance to a liquid stream
|
– A support of a conducted asterisk
|
Porosity presence, leak through sealing rings, damage or закупоривание highways
|
– The distributive panel and a lining, the control panel and linings
|
Porosity presence, mixture from normal position, перетечка liquids between channels, high resistance to a liquid stream
|
Tape brake of transfer of a backing and 1 transfer, сервоцилиндр
|
There is no inclusion, slipping
|
– The piston
|
Breakage, jamming
|
– Piston consolidations
|
Leak of a working liquid
|
– A rod and a spring
|
Jamming
|
– A cover сервоцилиндра
|
Breakage, easing of fastening leak of a working liquid
|
– A brake tape
|
Breakage, deterioration, displacement from normal position
|
– A pin
|
Breakage
|
– Hydraulic highways
|
Breakage, deformation, закупоривание, absence of sealing rings, leaks of a working liquid
|
– Carter of transmission
|
Porosity, leaks of a working liquid or high resistance to a liquid stream
|
Mechanical drive of the switch of ranges
|
Detachment, displacement
|
Zolotnik of the switch of ranges
|
Detachment, displacement
|
The ball return valve 1 (LO/PRN)
|
Absence
|
Level of a working liquid
|
Low level
|
Pressure of a working liquid
|
|
The first transfer, slipping of frictional knots on the first transfer does not join
Possible code of malfunction:
– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – an unstable or chaotic signal
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
TO CHECK UP | THE REASON |
Friction clutch of transfers of a forward course
|
Absence of inclusion, friction clutch slipping
|
– The piston in gathering with consolidation
|
Jamming, presence of cracks, leaks of a working liquid
|
– Internal consolidation
|
Zakuporivanie apertures
|
– Friction clutch disks
|
Deterioration of overlays, breakage шлицевых teeths
|
– A spring ring
|
Displacement from normal position
|
– The case
|
Presence of cracks, закупоривание highways
|
– A stopper of the case and the ball valve in gathering
|
Absence or displacement from normal position
|
– Springs
|
Jamming
|
МСХ braking by the engine
|
Breakage, проворачивание
|
МСХ 1st transfers
|
Breakage, проворачивание
|
Highways of a supply of a liquid to a piston cavity of a friction clutch of transfers of a forward course
|
Leak of a liquid or high resistance to a liquid stream
|
– Tubes of a supply of a liquid
|
Deformation, breakage, leak through a sealant ные rings, закупоривание
|
– A support of a friction clutch of transfers of a forward course
|
Porosity presence, leak through sealing rings, damage or закупоривание highways
|
– The distributive panel and a lining
|
Porosity presence, mixture from normal position, перетечка liquids between channels, high resistance to a liquid stream
|
– The block of the relay of pressure
|
Негерметичность consolidations of the block of the relay of pressure
|
ЭМК the switch And
|
Impossibility to include ЭМК, liquid leak
|
The valve of the switch of transfers 1-2
|
Zolotnik jamming in position of 2nd transfer
|
ЭМК the switch In
|
Impossibility to switch off ЭМК, закупоривание a drain aperture
|
Zolotnik and mechanical drive of the switch of ranges
|
Mixture of a zolotnik from normal position
|
The hydrotransformer
|
Проворачивание МСХ reactor GT
|
Pressure of a liquid in the trunk main
|
Low pressure
|
The second transfer, slipping of frictional knots on the second transfer does not join
Possible code of malfunction:
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
TO CHECK UP
|
THE REASON
|
Friction clutch of 2nd transfer
|
Absence of inclusion, friction clutch slipping
|
– The piston in gathering with consolidation
|
Jamming, presence of cracks, leak of a working liquid
|
– Friction clutch disks
|
Deterioration of overlays, breakage шлицевых teeths
|
– A spring ring
|
Displacement from normal position
|
– Springs
|
Jamming
|
– A support of a conducted asterisk
|
Damage presence of cracks, закупоривание apertures
|
Highways of a supply of a liquid to a piston cavity of a friction clutch of 2nd transfer
|
Leak of a liquid or high resistance to a liquid stream
|
– The control panel, a lining and a distributive plate, the distributive panel and linings: a support of a conducted asterisk
|
Porosity presence, mixture from normal position, fastening easing, high resistance to a liquid stream, a liquid overflowing between channels
|
МСХ 2nd transfers
|
Breakage, проворачивание
|
ЭМК the switch And
|
Jamming in the included position, закупоривание
|
The distributor and zolotnik of a gear change 1-2
|
Jamming in position of 1st transfer
|
Pressure of a liquid in the trunk main
|
Low pressure
|
Демпфер gear changes 1-2
|
Liquid leak through piston consolidations
|
Porosity of the distributive panel or картера
|
The distributor and zolotnik демпфера
|
Jamming
|
The third transfer, slipping of frictional knots on the third transfer does not join
Possible codes of malfunctions:
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
TO CHECK UP | THE REASON |
Friction clutch of 3rd (direct) transfer
|
Absence of inclusion, friction clutch slipping
|
– The piston in gathering with consolidation
|
Jamming, presence of cracks, leak of a working liquid
|
– Disks
|
Deterioration of overlays, breakage шлицевых teeths
|
– A spring ring
|
Displacement from normal position
|
– Springs
|
Jamming
|
– The case of a friction clutch and an entrance shaft
|
Damage presence of cracks, закупоривание apertures
|
– A stopper of the case and the ball valve in gathering
|
Absence or fastening easing
|
Highways of a supply of a liquid in a piston cavity of a friction clutch of 3rd transfer
|
Presence of porosity displacement from normal position, easing кропления, перетечка liquids between channels, high resistance to a liquid stream
|
– The control panel, linings and a distributive plate, distribute тельную the panel and a lining, a support of a conducted asterisk
|
– Consolidations of a support of a conducted asterisk
|
Liquid leak
|
– An entrance shaft
|
Негерметичность consolidations
|
Plug damage, mixture from normal position
|
ЗМК the switch In
|
Jamming in the switched off position, liquid leaks
|
The distributor and zolotnik of a gear change 2-3
|
Jamming
|
Демпфер gear changes 2-3
|
Liquid leak through piston consolidation
|
Porosity of the distributive panel or картера
|
The distributor and zolotnik демпфера 2-3
|
Jamming
|
The ball return valve 5 (inclusions of a friction clutch 3 and transfers)
|
Absence
|
Pressure of a liquid in the trunk main
|
Low pressure
|
The fourth transfer, slipping of fractional knots on the fourth transfer does not include
Possible codes of malfunctions:
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
TO CHECK UP
|
THE REASON
|
Tape brake of 4th transfer and сервоцилиндр
|
Absence of inclusion, slipping
|
– The piston сервоцилиндра
|
Breakage, jamming
|
– Piston consolidations
|
Liquid leak
|
– A piston and spring rod
|
Jamming
|
– A servo-driver cover
|
Breakage, fastening easing, liquid leak
|
– A tape
|
Breakage, deterioration, displacement from normal position
|
– Carter
|
Crack about a tape arm
|
Highways of a supply of a liquid to сервоцилиндру
|
Porosity, displacement from normal position, fastening easing, the big resistance to a liquid stream, liquid leak between channels
|
– The valve case, a lining and a distributive plate, the distributive panel, картер
|
ЭМК the switch And
|
Jamming in the switched off position
|
The distributor and zolotnik a rekey ния transfers 3-4
|
Jamming
|
Zolotnik of the switch of ranges
|
Displacement from normal position (in position of a range 3)
|
Демпфер gear changes 3-4
|
Liquid leak through piston consolidation
|
Porosity of the distributive panel or картера
|
The distributor демпфера 3-4
|
Jamming
|
Pressure in the trunk main
|
Low pressure
|
The car does not get under way from a place
TO CHECK UP
|
THE REASON
|
The hydrotransformer
|
Breakage of assembly ledges, destruction of welded seams
|
Cut of fixing bolts
|
Deterioration шлицев a turbine shaft
|
Breakage of shovels of wheels
|
Case cracks on welded seams
|
Shaft of a turbine wheel
|
Removal or cut шлицев
|
The hydropump
|
Jamming or breakage of plates of a rotor
|
Shaft of a drive of the hydropump
|
Breakage a cut or смятие шлицев
|
The filter and filter consolidation
|
Забивание, absence
|
Level of a working liquid
|
Low level of a working liquid
|
Mechanical drive of the switch of ranges
|
Detachment
|
Chain transfer, asterisks and a chain
|
Breakage
|
Planetary transfer
|
Breakage, absence of greasing
|
The main transfer
|
Gear wheel breakage, absence of greasing
|
The distributive panel and lining
|
Damage, liquid leak, displacement from normal position
|
The control panel, a lining and a distributive plate
|
Damage, liquid leak, displacement from normal position
|
МСХ and a friction gear of a forward course. МСХ 1st transfers
|
Damage, проворачивание
|
Deterioration of dynamics of the car
Possible codes of malfunctions:
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
TO CHECK UP
|
THE REASON
|
Level of a working liquid
|
Low level of a liquid
|
ЭМК gear changes
|
Both ЭМК are switched off, the car gets under way on 2 transfer
|
ЭМК the switch In it is not switched off
|
System of blocking ГТ
|
Jamming in the included position or incomplete deenergizing of a friction clutch of blocking ГТ
|
The hydrotransformer
|
Damage or contamination
|
Engine stop
TO CHECK UP
|
THE REASON
|
System of blocking ГТ
|
Jamming in the included position or incomplete deenergizing of a friction clutch of blocking ГТ
|
– ЭМК a friction clutch of blocking ГТ
|
Jamming in the included position, закупорива ние a drain aperture
|
– The distributor of management of a blocking friction clutch
|
Jamming in position of inclusion of a friction clutch
|
Join only 1st and 2nd transfers
Possible codes of malfunctions:
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
TO CHECK UP
|
THE REASON
|
ЭМК the switch In
|
Jamming in the switched off position, liquid leak through the valve, refusal of an electric chain
|
The distributor and zolotnik a rekey ния transfers 2-3
|
Jamming in position of inclusion of 2nd transfer
|
ЭМК the switch And
|
Jamming in included position, закупорива ние the valve, refusal electric chains
|
2nd join only and 3rd transfers
Possible codes of malfunctions:
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
TO CHECK UP
|
THE REASON
|
ЭМК the switch And
|
Jamming in included position, refusal electric chains, liquid leak through the valve
|
3rd and 4th transfers join only
Possible codes of malfunctions:
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
TO CHECK UP
|
THE REASON
|
ЭМК the switch In
|
Jamming in the included position, закупорива ние the valve, refusal of an electric chain
|
The distributor and zolotnik a rekey ния transfers 2-3
|
Jamming in position of inclusion of 3rd transfer
|
Range P (parking) does not join
TO CHECK UP
|
THE REASON
|
The mechanism of inclusion of blocking of a target shaft
|
Bend or rod damage
|
Breakage or spring jamming
|
Detachment of a rod from the stopper lever
|
Roller and spring
|
Easing of an inhaling of a bolt
|
Bend or damage
|
The stopper lever
|
Damage, fastening easing (absence of a pin of a rod)
|
Zolotnik of the switch of ranges
|
Displacement from normal position, deformation of a drive of the lever of a stopper
|
Cogwheel, the blocking mechanism
|
Damage of teeths or шлицев
|
Stopper
|
Damage, breakage of teeths
|
Stopper spring
|
Breakage, absence
|
Drive of the mechanism of blocking
|
Adjustment infringement
|
Noise of a gnash of teeths
TO CHECK UP
|
THE REASON
|
Stopper
|
Damage, easing or detachment of a returnable spring
|
Inefficient braking by the engine on all ranges
TO CHECK UP
|
THE REASON
|
Friction clutch of braking by the engine
|
Absence of inclusion, slipping
|
– The piston and consolidation
|
Jamming, cracks of leak of a liquid
|
– Disks
|
Deterioration of frictional overlays, breakages шлицов
|
– Springs
|
Jamming
|
– The case and an entrance shaft
|
Damage, cracks, закупоривание channels
|
– A stopper of the case and the ball valve in gathering
|
Absence or fastening easing
|
Highways of a supply of a working liquid to a piston cavity of a friction clutch
|
Porosity, mixture from normal position, fastening easing, resistance to a liquid stream, liquid leak between channels
|
– Linings of the control panel and a distributive plate, distribute тельную the panel and a lining, a support of a conducted asterisk
|
Liquid leak
|
– Consolidations, a support of a conducted asterisk
|
Негерметичность consolidations
|
– An entrance shaft
|
Damage or displacement from normal position of the plug
|
Level of a working liquid and pressure in the trunk main
|
Low pressure or level
|
The distributor and zolotnik of a gear change 3-4
|
Zolotnik jamming in position of 4th transfer
|
Zolotnik of the switch of ranges and its drive
|
Displacement from normal position
|
Inefficient braking by the engine in a range 2
Possible codes of malfunctions:
– 1810 Malfunction of the switch of the control of ranges (the block of the relay of pressure)
TO CHECK UP
|
THE REASON
|
Friction clutch of braking by the engine
|
Absence of inclusion, slipping
|
Tape brake 4 transfers
|
Absence of inclusion slipping
|
The block of the relay of pressure
|
Liquid leak, the relay it is not efficient
|
Inefficient braking by the engine in a range 1
Possible codes of malfunctions:
– 1810 Malfunction of the switch of the control of ranges (the block of the relay of pressure)
TO CHECK UP
|
THE REASON
|
Friction clutch of braking by the engine
|
Absence of inclusion, slipping
|
Сервоцилиндр a tape brake of 1st transfer and backing transfer
|
Absence of inclusion, slipping, absence of inclusion of a tape brake of 1st transfer and backing transfer
|
The block of the relay of pressure
|
Liquid leak, the relay it is not efficient
|
The step-by-step return valve 1
|
Absence
|
Трогание the car at included range N
TO CHECK UP
|
THE REASON
|
Friction clutch of transfers of a forward course
|
It is not switched off
|
Friction clutch of transfer of a backing and сервоцилиндр a tape brake of 1 transfer and backing transfer
|
Both frictional elements are not switched off
|
Zolotnik of the switch of ranges and its drive
|
Displacement from normal position
|
Ranges do not join
TO CHECK UP
|
THE REASON
|
Zolotnik of the switch of ranges and drive of the lever of a stopper
|
Breakage, absence
|
Detachment from a zolotnik of the switch of ranges
|
Clamp of draught of a zolotnik of the switch of ranges
|
Detachment
|
Zolotnik of the switch of ranges
|
Jamming
|
Mechanical drive of the switch of ranges
|
Detachment
|
The control panel, the distributive panel and картер
|
Забивание hydraulic channels
|
The indicator selector position does not correspond to the chosen range
TO CHECK UP
|
THE REASON
|
Selector drive
|
Adjustment infringement
|
Spring and stopper roller
|
Breakage, absence
|
Easing of an inhaling of a bolt
|
Zolotnik of the switch of ranges
|
Detachment from the stopper lever
|
Leaks of a working liquid
To execute diagnostics of leak of a working liquid.
Foaming of a working liquid
TO CHECK UP
|
THE REASON
|
Working liquid
|
Hit in a working liquid of a cooling liquid of the engine
|
Too high level of a working liquid
|
The filter of a working liquid
|
Забирание
|
Presence of cracks
|
Filter consolidation
|
Liquid leak
|
Engine condition
|
Engine overheat
|
Car condition
|
Car overload
|
Vibration
TO CHECK UP
|
THE REASON
|
The hydrotransformer
|
Balancing infringement
|
Breakages of internal details
|
Transmission and the Engine
|
Displacement from normal position
|
Target shaft, semiaxes
|
Balancing infringement
|
Deterioration or damage of plugs
|
Turbine shaft
|
Deterioration of plugs
|
Balancing infringement
|
The friction clutch of blocking of the hydrotransformer, slipping or too slow inclusion of a friction clutch does not join
Possible code of malfunction:
– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – an unstable or chaotic signal
– 703 Malfunction of the switch of a stoplight
– 712 Gauge of temperature of a working liquid of transmission – a signal low voltage
– 713 Gauge of temperature of a working liquid of transmission – a signal high voltage
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 741 Chain of management of a friction clutch of blocking ГТ, jamming ЭМК in the switched off position
– 742 Chain of management of a friction clutch of blocking ГТ, jamming ЭМК in the included position
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 1560 Deviation of pressure of an electric network from norm
– 1810 Malfunction of the switch of the control of ranges (blocking of the relay of pressure)
– 1812 Overheat of a working liquid of transmission
– 1887 Relays of pressure of a friction clutch of blocking ГТ
TO CHECK UP
|
THE REASON
|
ЭМК a friction clutch of blocking ГТ
|
Jamming in the switched off position
|
Leak of a working liquid through a sealing ring
|
Absence of pressure on winding ЭМК
|
Transmission electroconducting
|
Bad electric contacts
|
Jamming wires (short circuit)
|
Damage of an electric socket
|
БУТ
|
Absence of operating signal ЭМК
|
Overheat of a working liquid
TO CHECK UP
|
THE REASON
|
The hydrotransformer
|
Breakage of internal details
|
Hydraulic system of a friction clutch of blocking ГТ
|
Leak of a working liquid
|
Hydrodistributors of management of a blocking friction clutch
|
Zolotnik jamming in position of deenergizing of a friction clutch of blocking
|
Level and pressure of a working liquid
|
Low level or pressure of a working liquid
|
The blocking friction clutch is not switched off
TO CHECK UP
|
THE REASON
|
ЭМК a friction clutch of blocking ГТ
|
Jamming in the included position
|
Закупоривание a drain aperture
|
Short circuit on "weight"
|
The hydrotransformer
|
Breakage of internal details
|
Hydrodistributors of management of a blocking friction clutch
|
Zolotnik jamming in position of deenergizing of a friction clutch of blocking
|
Premature blocking of the hydrotransformer before engine warming up
TO CHECK UP
|
THE REASON
|
The gauge of temperature of a cooling liquid of the engine
|
Infringement of normal work
|
Noise
MALFUNCTION SIGN
|
TO CHECK UP
|
THE REASON
|
On all ranges howling noise which depends on frequency of rotation of a shaft of the engine or disappears at blocking ГТ
|
The hydrotransformer
|
To check up that a noise source is ГТ. For this purpose at included range D to press one-times but for a brake pedal (the left foot) and a pedal of an accelerator and quickly to muffle the Engine. Noise ГТ increases at loading increase on ГТ
|
Howling noise of a high-pitch tone which increases at increase of turns of the engine or is sensitive to size of pressure of a working liquid
|
The hydropump and its drive
|
To check up that a noise source is the hydropump (simultaneously with pressure check in the trunk main). Pressure increase results to growth of noise of the hydropump
|
The sound similar to crackling of roasted corn grains
|
|
The hydropump works in a mode кавитации which is shown available vials on probeе
|
Liquid leak through seams of the case of the filter
|
Damage or mixture from normal position of consolidation of the mesh filter
|
Rumble or jingling sound of a high-pitch tone
|
Condition of pipelines of the heat exchanger of a working liquid of transmission Absence of a contact of pipelines with a surface of a radiator and with other tubes
|
To check up presence fluctuation of pressure the worker of a liquid on trembling of an arrow of a manometre
|
The howling or roaring sound amplifying and decreasing depending on speed of the car: the most appreciable at dispersal with small acceleration
|
Knot of chain transfer
|
|
To check up that a noise source is the chain and-or asterisks. For this purpose it is necessary to press the left foot a brake pedal and to translate the selector from range D in range R. If noise has stopped, to check up the following
|
|
Chain
|
Chain lengthening
|
Leading and conducted asterisks
|
Breakage or cut of teeths
|
Development of working surfaces of teeths
|
Development of an internal ring or bodies качения the needle bearing of a nave of an asterisk
|
Bearing damage
|
Noise of the main transfer (rumble), is most strongly shown at dispersal with small acceleration and-or at movement on turn
|
Supports of leading and conducted asterisks
|
Development of an internal ring of the needle bearing of a nave of an asterisk
|
Knot of the main transfer
|
Deterioration of satellites or washers
|
– Gear wheels (solar, satellites) the main transfer
|
Damage or deterioration of teeths
|
The differential case
|
|
– Semiaxial gear wheels of differential
|
|
Transmission noise on 1st, 2nd, 3rd or 4th transfer
|
Solar gear wheel of the main transfer
|
Deterioration and fatigue failures of teeths of gear wheels
|
– Satellites of the main transfer
|
Damage of a persistent washer
|
Transmission noise only on some ranges
|
By means of the table of inclusion of frictional operating elements to track a capacity tray through a transmission in an operating mode with the raised noise and to check up the mechanisms loaded on corresponding transfers and ranges
|
Deterioration or damage of gear wheels
|
|
|