Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
- 8. The electronic block of management and gauges
- 8.2. Gauges
8.2.2. The gauge of temperature of air in an inlet collector (pipeline) (ДТВ)
8.2.3. The gauge of concentration of oxygen in the fulfilled gases (ДКК)
8.2.4. The gauge of position throttle заслонки (ДДЗ)
8.2.5. The gauge of absolute pressure in the inlet pipeline (ДАД)
+ 8.2.6. The gauge of speed of the car (ДСА)
8.2.7. The gauge of inclusion of a central air of air
8.2.8. Switch "Parking" / a neutral (an automatic transmission)
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment
|
Switch "Parking" / a neutral
Switch "Parking" / a neutral and the switch of a lantern of a backing
|
|
1. The BOLT, MOMEIT INHALINGS of 30 Nanometers
2. THE SWITCH
3. THE PLATEN OF SWITCHING OF RANGES
4. THE ADJUSTING APERTURE IN THE SWITCH CASE
5. The MEASURING CORE in DIAMETER of 2,34 mm |
Electric socket of the switch with the T-shaped clamp
|
|
1. SWITCH "PARKING" / THE NEUTRAL AND THE SWITCH OF THE LANTERN OF THE BACKING
2. THE SWITCH SOCKET THE T-SHAPED PAD OF THE CLAMP |
Switch "Parking" / a neutral is intended for the control over position of the selector of an automatic transmission. The switch signal is used ECU at management of the valve of idling of the engine.
The prevention Car operation is forbidden at the disconnected socket of switch "Parking" / a neutral as it will lead to infringement of work of the engine idling. Delivery of a code of malfunction 24 (refusal of the gauge of speed of the car) is possible also.
To remove or disconnect
| PERFORMANCE ORDER |
| 1. A mechanical drive of the selector of ranges. |
| 2. An electric socket. |
| 3. Fixing bolts. |
| 4. The switch. |
|
SWITCH REPLACEMENT – INSTALLATION OF THE SWITCH WHICH WAS IN THE USE
To establish or attach
| PERFORMANCE ORDER |
| 1. To turn the platen of switching of ranges in neutral position. |
| 2. The switch, сориентировав its aperture on лыскам the platen. |
| 3. To screw, without tightening, bolts. |
| 4. To insert into an adjusting aperture of the case of the switch a measuring core and to turn the switch so that a core it was drowned on 9 mm. |
| 5. To tighten bolts. |
|
To remove or disconnect
| PERFORMANCE ORDER |
To take out a core.
The prevention After switch adjustment it is necessary to check up blocking of start-up of the engine in all positions of the selector of ranges, except a neutral and "Parking". If the engine is started and in other positions of the selector, to repeat adjustment.
|
|
SWITCH REPLACEMENT – INSTALLATION OF THE NEW SWITCH
To establish or attach
| PERFORMANCE ORDER |
| 1. To turn the platen of switching of ranges in neutral position. |
| 2. The switch, сориентировав its aperture on лыскам the platen. |
3. To screw and tighten bolts. If apertures for bolts do not coincide with carving apertures in картере transmissions, it is necessary to check up position of the platen and to establish it in neutral position, without turning the switch. The switch is in neutral position. If the switch has been turned, it is necessary to adjust it to similarly switch which was in the use.
The prevention After switch adjustment it is necessary to check up blocking of start-up of the engine in all positions of the selector of ranges, except a neutral and "Parking". If the engine is started and in other positions of the selector, to make the adjustment applied at installation of the switch which was in the use.
|
|
To adjust
| PERFORMANCE ORDER |
| 1. To translate the selector of ranges in neutral position. |
| 2. To weaken fixing bolts of the switch. |
| 3. To turn the switch on the platen before coincidence of an adjusting aperture of the switch to an aperture in a pad of the holder. To insert a measuring core in diameter of 2,34 mm on depth of 15 mm. |
| 4. To tighten bolts the demanded moment. |
| 5. To take out a measuring core. |
|
|
|
